If you’re looking for axle washers, you’ve come to the right place. We stock a wide variety of axle washers, so you can find the perfect fit for your vehicle. Whether you’re looking for a specific size or a certain type of axle washer, we’ve got you covered. So come on in and take a look around. We’re sure you’ll find what you need.
Axle Washers
- HIGH-QUALITY SPRING STEEL PUSH-ON PUSHNUTS FOR LOW TORQUE APPLICATIONS - These pushnuts may not look that much with their .02-inch thickness and simple design but they are one of the most efficient ways to keep wheels in place for low-torque outdoor equipment like dollies, hand carts, and lawn wagons.
- PERFECT ALTERNATIVE FOR PINS AND WASHERS - Same function but one is more efficient. These pushnuts have teeth that slide into the stud with a ratcheting action, only allowing the pushnuts to move in one direction and resist moving to the opposite direction.
- DOLLY WHEEL LOCK WASHERS FITS 5/8" DOLLY AXLE RODS - With an outer diameter of 1 inch, these pushnuts can fit unthreaded 5/8-inch dolly axle rods snugly. It has a diameter tolerance of about .002 inches for maximum holding strength.
- OILED PHOSPHATE FINISH - Phosphate coatings prevent corrosion on steel parts. It has a strong surface adhesion, preventing wear and improving friction-induced wear. The oil on the pushnuts' phosphate coating serves as a sealer to ensure the effectiveness of the phosphate's corrosion-resistant properties.
- BEST VALUE 8-PACK DOLLY WHEEL LOCK WASHERS - Are you frustrated about searching for hard-to-find parts? Single-use pushnuts? There's no turning back once you've already removed them. Thankfully, this 8-pack variation will provide you a supply of pushnuts that's enough to last one dolly's lifespan.
- Trailer Nut Set
- 1" Washers & 2"Cotter Pins
- Material: strengthen material,longer life.
- Factory sells in direct, the quality is assured
- 4 Pcs Spindle "D" Washer.
- 1" I.D. x 1 5/8" O.D. "D" Washer.
- 1/8" Thick .
- Will fix 3.5K & 6K Regular Duty.
- Fits for Dexter Axles With and W/O EZ Lube.
- 2 6-Slot Spindle Nuts 1"-14
- 2 1" D Washer2
- 2 1" Tang Washers
- ✔️ [Castle Nut] - Castle Spindle Shaft Nut "1 ID
- ✔️ [Shaft Washer] - Shaft Washer 1" ID
- ✔️ [Cotter Pin] - Cotter Pins 1-3/4" long
- ✔️ [T Washer] - 2 Pieces
- High Quality 7 Kinds Metric M3 M4 M5 M6 M8 M10 M12 Stainless Steel Starlock Push on Washers Assortment kit total 350Pieces
- Starlock Washer;External Push Rings; Push On Washers;Speed Clips;Push Nuts for Unthreaded Shafts
- Material:304 stainless steel;304 stainless steel have good chemical resistance and may be mildly magnetic
- Widely used in machinery equipment, industrial production of shock absorption ,bearings, machinery etc
- All contained in a compact and see through compartmented plastic Box.100% new,Perfect accessories of shock absorption for machinery equipment.Easy to install and durable to use
- Package Dimensions: 4.33 L x 1.83 H x 3 W (inches)
- Package Weight: 0.35 pounds
- Country of Origin : United States
- Part Number: 618057
- ✅Fits ALL 4 thicker wheel hub washers for all years RZR 1000 XP or RZR Turbo.
- ✅These take place of the thin weak 2 washers that go between top of axle nut and top of the wheel hub. Use 1 per hub to replace both the crushed oem washers and take the left to right play out of wheel hub which helps wheel to stay tight and makes wheel bearings last longer!
- ✅Made from high-quality materials for ultimate durability and perfect match. Brand new with good performance.
- ✅Package Includes: 4pcs set
- ✅1 Year Unlimited-mileage Quality Guarantee
- Used to replace electric bike hub motor nuts, usually for 250W-500W motors with 12mm shaft.
- The motor screws are made of steel and rubber materials, which are very durable.
- E-Bike hub motor screw nut fit for most bicycle replecement, electric bike, scooter, e-bike, etc.
- They can also be used as axle spacers in conjunction with torque arms on more powerful motors.
- Please carefully confirm the thread size before purchasing.
- Nice set: the package comes with 12 pieces of bike nuts, available in M10, 3/ 8 M16, 5/ 16 M18 these models, and 4 pieces of M8 safety washers, 8 pieces of M10 safety washers, 24 pieces in total, a sensible set to meet your various using needs
- Sturdy and long lasting to use: these flange nuts are made of sturdy steel, strong and solid, hard to break, bend or deform, coming from exquisite workmanship, bike wheel nuts are not easy to rust or corrode, with long term service life, making sure a comfortable using experience
- Fit most bicycles: those bicycle wheel nut and safety washer are reliable to use, functional parts for your bike wheel, fit a variety of bicycles, such as road bikes, mountain bikes, children's bicycles, folding bicycles and so on
- Thoughtful designs: these little nuts are designed with deep threads and even pitch, adopting polishing technology, smooth on surface, applied well with other parts; In addition, these retaining clip hook increase the contact area, reduce the pressure, keep the nut from falling loose
- Size information: the front safety washer is about 8 mm/ 0.31 inch in inner diameter, 19 mm/ 0.75 inch in outer diameter, 26 mm/ 1.02 inches long, its hook is approx. 4.69 mm/ 0.18 inch wide, 6.9 mm/ 0.27 inch high, 2 mm/ 0.08 inch thick; The rear safety washer is about 10.9 mm/ 0.43 inch in inner diameter, 18.7 mm/ 0.74 inch in outer diameter, 26 mm/ 1.02 inches long, its hook is approx. 4.69 mm/ 0.18 inch wide, 6.9 mm/ 0.27 inch high, 1.8 mm/ 0.07 inch thick
What are Axle Washers?
Axle washers are designed to prevent the spring bolts from loosening. These smallle spring bolts can work loose due due to vibrations and wear. The spring bolts can hit the axle housing, which causes abras damage to both the axle and the spring. These washers are designed to prevent this problem from occurring, and they are often easy to replace.
Axle washers are round, flat washers that are placed on either side of the spring bolts. They fit between the axle and the spring, and they are designed to prevent the bolts from hitting the axle housing. This prevents the bolts and the housing from becoming damaged. The washers absorb some of the vibration from driving, which can also help prevent the bolts from loosening.
There are two main types of axle washers: locking wash washers and flat washers. Locking washers have designed to lock the nuts in place, while flat washers are simply round, flat discs. They do not lock the nuts in place, but they are almost always used with locking washers.
What are Axle Washers?
People who don’t know cars often wonder, “what is an axle washer and why do I need one?” Well, axle washers are small parts, usually made of steel, bronze fasters that go between the axle and the hub to maintain a tight fit. They come in different sizes and shapes. There are five different types of axle washers.
Like any part you put on your vehicle, axle washers need to be maintained. The friction of the wheels can cause the axle washer to wear down over time and create some nasty squeaks. If the axle washer wears worn, it needs to be replaced. When replacing you replace your axle washer will depend on how you drive your vehicle. It’s important to regularly check the axle washers to determine when you need to replace them.
But for most vehicles, axle washers are relatively cheap and easy to replace. Ax trusted service technician can help you determine when you need to replace your axle washer.
How to Choose the Right Axle Washers for Your Vehicle
Your vehicle’s axles are vital to keeping you safe on the road. They are just as important as other safety features on your vehicle, such as brake pads and windshield wipers. Axles are a pair of rods that rotate the wheels, supporting the weight of your vehicle. This means that they incur a lot of stress over time. It’s crucial that your axles, as well as the CV joints that connect them to the wheels, remain lubricated. This is where axle washers come into play.
Although axle washers are tiny components they play a huge part in the safety and performance of your vehicle. These washers are what helps trap lubricating grease within your CV joints, which keep your axles turning freely. Once the washers wear out, they begin their ability to hold lubrication, ultimately resulting in a restricted range of motion for your wheels.
When it’s time to invest in new axle washers, you’ll need to choose the right ones for your vehicle. Choosing the wrong axle washers can spell disaster for the safety and performance of your vehicle, so it’s important to know what to look for.
There are several different types of axle washers on the market, including with its own unique characteristics. The two most common types of axle washers are rubber and metal. Rubber axle washers are much more affordable, but they tend to lose their shape over time and break easier than metal ones. Metal axle washers, on the other hand, may be more expensive than their rubber counterparts, but they’re also more durable. They are less likely to lose their shape and break over time.
As mentioned, choosing the right axle washers for your vehicle is crucial to the safety and performance of your vehicle. It’s important to know what to look for when choosing the right axle washers, including: the material,’re made of, the size and shape of the washers.
To help you figure out which type is best for your vehicle, we’ve put together this handy guide to choosing the right axle washers for your vehicle.
Metal Axle Washers
These axle washers are much more durable than rubber ones, but they are also more expensive. They are less likely to lose their shape over time, breaks easier than rubber ones.
Rubber Axle Washers
These axle washers are much more affordable than metal ones, but they tend to lose their shape over time and break easier than metal ones.
Looking For Axle Washers?
Whether you need looking to replace your current axle washers or are want to learn more about what’s involved in choosing the right ones for your vehicle, we’ve put together this handy guide to help you out. With this information in hand, you’ll be able to find the right axle washers for your vehicle and keep it running smoothly.
How to Install Axle Washers on Your Vehicle
If your vehicle is equipped with drum brakes, chances’re mounted on the rear of the axle shaft, which sits the at the rear of the wheel. The brakes are are mounted to the hubs that are attached to the axle shaft, which means you’ll need to remove the hub in order to install the axle washers. Once you’ve located where your vehicle’s axle, follow these steps:
1. Jack Up Your Vehicle and Secure it with Jack Stands
To the floor jack to raise up the vehicle. you can place a jack stand under the axle for added safety; case the jack slips.
2. Remove The Wheel and Brake Drum
Unbolt the drum from the hub with a tire iron. Lo should be six lug nuts holding the drum to the hub. After the drum is removed, slide the hub off the axle. You may see a seal between the hub and the axle shaft.
3. Slide The Axle Washers Onto The Axle
Slip the axle washers on the axle shaft and use a small clamp to hold them in place until you’re ready to install them on the hub.
4. Replace The Hub Ont the Axle and Reattach the Brake Drum
Use the tire iron to slide the hub back onto the axle. align your new axle washers should now be securely installed. Re the brake drum back onto the hub.
5. Replace The Wheel and Lower the Vehicle
Tighten the lug nuts as much as you can with the tire iron, then lower the vehicle back onto the ground. Use the lug nut wrench to finish tightening the lug nuts as much as possible. Reinstall the wheel cap and put the lug nuts.
6. Test Drive Your Vehicle and Check for Leaking Brake Fluid
Drive around the block and check for leaking brake fluid. If there’s a leak, repeat the entire procedure until there find’t see leaking fluid. Le, your repair should be good to go. Ax this point, you’ve successfully installed the axle washers on your vehicle.
How to Test Your Axle Washers for Leaks
A leaky axle washer can cause your vehicle to emit a clicking sound as it drives, especially when making a at slow speeds. When your axle washer leaks, grease escapes and the axle boots exposed.